8 CYL. 6.0L - DIESEL-Fuel control module, sensor & related parts

SPACER UNDER PEDESTAL

#3C34 8599-AA - (NAVISTAR ID 1840603C92) - HEATER SUPPLY TUBE THAT CONNECTS TO THE FRONT COVER, ALSO HAS AN ATTACHMENT POINT TO THE INTAKE MANIFOLD

#3C34 8599-AB - #1840603C93 (INTERNATIONAL) - ONE END OF TUBE BOLTS TO HEATER HOSE AND THE OTHER END BOLTS TO THE FRONT COVER WHICH IS THE ONLY END WITH A GASKET - 3C3Z-9J469-AA(GASKET)

BLUE HOSE THAT CONNECTS 9P456 COOLER TO 9P458. (OEM HOSE WAS ORANGE).

UPPER. BLUE GASKET(NOT SERVICED SEPARATELY). INCLUDES HEATER INLET TUBE 18599

UPPER

LOWER. INCLUDES 9461 GASKETS

INCLUDES 8C368 CROSSOVER WITH SMALL WATER FITTING FOR HEATED THROTTLE BODY

KIT-INTAKE MANIFOLD AND RELATED PARTS

KIT-INTAKE MANIFOLD AND RELATED PARTS. # 1845151-C91

BOLT; M6 X 25MM

BOLT; M6 X 95MM

STUD; M6 X 95MM

INTAKE GASKETS WITH TURBO MOUNTING HARDWARE.

INTAKE MANIFOLD GASKET WITH EGR COOLER SEALS.

ONE PACKAGE CONSISTS OF TWO PIECES

ONE PACKAGE CONSISTS OF 2 PIECES. TWO(2) PIECES REQUIRED PER ENGINE

RH

LH

ALSO SERVICED IN 6B898/9424/9433/9P456. ONE PACKAGE CONTAINS 2 GASKETS. TWO(2) GASKETS REQUIRED PER ENGINE

PCV FITTING(WISHBONE). ALSO SERVICED IN 9A589. MTG SCREWS W506962-S437

FITTING-MAP SENSOR. #1838345-C1

Снято с производства

INTL# 1845851-C91. ALSO SERVICED IN 9424

GASKET-EGR COOLER, FRONT. GASKET BETWEEN EGR COOLER AND BOTTOM OF INTAKE MANIFOLD.

GASKET-EGR COOLER, REAR

SHIELD; LOCATED AT RIGHT REAR OF INTAKE MANIFOLD

SHIELD; LOCATED AT REAR OF INTAKE MANIFOLD.

BOLT; M10 X 16MM; RETAINS REAR INTAKE MANIFOLD SHIELD.

BOLT; M6 X 14MM; RETAINS REAR INTAKE MANIFOLD SHIELD.

NUT; M6; RETAINS RIGHT INTAKE MANIFOLD SHIELD.

SEAL-EGR COOLER. 27MM OD X 4MM.

16MM OD X 2MM THICK. ALSO SERVICED IN 6N853 OIL TUBE CONNECTOR AND WITH 9K024 PLUG

16MM OD X 2MM THICK.

16MM OD X 2MM THICK.

#1838615-C1. 2.1 INCHES IN DIA. ALSO SERVICED IN 9P458 ASSY.

#1838618-C1. 34MM OD X 5MM THICK. ALSO SERVICED IN 9P458 ASSY.

#1835339-C1. 22MM OD X 2MM THICK. ALSO SERVICED IN ENGINE HIGH PRESSURE PUMP KIT 9G804

#1836505-C1. 11MM OD X 2MM THICK. O-RING FOR CAM POSITION SENSOR

#1837799-C1. 14MM OD X 2MM THICK. O-RING FOR ECT AND EOP SENSOR

#1837800-C1. 14MM OD X 2MM THICK. O-RING FOR ICP SENSOR

#1837803-C1. 18MM OD X 2MM THICK. O-RING FOR MANIFOLD AIR TEMP. SENSOR

#1837889-C1. 10MM OD X 2MM THICK. O-RING FOR CAM POSITION SENSOR

#1839033-C1. 16MM OD X 2MM THICK. ALSO SERVICED IN DIAGNOSTIC VALVE 6K702 IN OIL COOLER

14MM OD X 2MM THICK. O-RING FOR PLUG ON FUEL FILTER HOUSING.

21MM OD X 4MM. SEAL BETWEEN HP PUMP AND ENGINE BLOCK.

COMPLETE SEAL KIT THAT ALSO COMES WITH OIL COOLER ASY. CONTAINS ALL SEALS REQUIRED TO R&R OIL COOLER.

SEAL FOR 9K024 ON H/P PUMP COVER

SEAL INSIDE FUEL FILTER HOUSING BETWEEN 9T289 & 9C166.

SENDER; ""BLACK'' 2 SPADE-TERMINAL CONNECTOR; #F65F 10884-AA.

NAVISTAR #1836537C91

MOUNTED ON CHARGE AIR COOLER MANIFOLD

NIPPLE EXITING WATER PUMP. O-RING IS 1825293C1.

3~8" HOSE NIPPLE ON FRONT RH AND BACK LH CYLINDER HEAD.

Снято с производства

ELBOW CONNECTING TO HEATER CORE.

ELBOW CONNECTING TO HEATER CORE.

ELBOW ON FRONT RH & REAR LH CYLINDER HEAD.

HEATER HOSE

PRESS IN HEATER HOSE FITTING WITH 1/4" FITTING ON THE SIDE.

THIS PART PRESSES INTO THE FRONT RIGHT MANIFOLD NEXT TO THERM. HOUSING AND HAS ONE NIPPLE FOR HEATER INLET HOSE

#3C34 8K528-AA - (NAVISTAR NO. 1838419C1)

Снято с производства

"45 DEG. " - 3/8'' - 18 - 5/8'' HOSE CONNECTION

Снято с производства