Кузовные панели — Теплозащита выпуска

Снято с производства

GASKET, BETWEEN EXHAUST MANIFOLD AND CONVERTER

Снято с производства

THIS IS THE U-BOLT PORTION OF THE U-BOLT ASY. (THE W700420-S403 SECURING NUTS ARE AVAILABLE SEPARATELY BUT THE BAR IS NOT. THE BAR IS ONLY AVAILABLE IN THE COMPLETE U-BOLT, BAR & NUT KIT, XS5Z-5K272-JA)

CONVERTER ASY

Снято с производства

BRACKET ASY, ENGINE TO CATALYST

Снято с производства

GASKET B, CONVERTER OUTLET, 2 BOLT HOLES

Снято с производства

BRACKET, FRONT MUFFLER SUPPORT. L-SHAPED ROD WELDED TO A 100X35MM BRACKET WITH TWO MOUNTING HOLES.

Снято с производства

INSULATOR

MUFFLER, FRONT

Снято с производства

MUFFLER, REAR

Снято с производства

BRACKET, STRAIGHT ROD, 6 1/4'' LONG

Снято с производства

INSULATOR - OVAL SHAPED

Снято с производства

RUBBER INSULATOR, MUFFLER SUPPORT - OVAL SHAPED

SHIELD, EXHAUST PIPE, UPPER HEELKICK

Снято с производства

SHIELD, UPPER REAR MUFFLER

Снято с производства

SHIELD, EXHAUST, UPPER FRONT

Снято с производства

HEAT SHIELD, UPPER AND FRONT

Снято с производства

HEAT SHIELD, UPPER AND CENTER

Снято с производства

THIS IS A COMPLETE U-BOLT, BAR & RETAINING NUT KIT. (THE U-BOLT IS AVAILABLE SEPARATELY AS XS8Z-5A231-AA, AS ARE THE W700420-S403 SECURING NUTS, BUT THE BAR IS NOT AVAILABLE SEPARATELY.)

LH MANIFOLD AND FRONT CONVERTER ASY. - (NOTE: FOR WARRANTY REPAIRS - CHECK FOR TECHNICAL SERVICE PUBLICTIONS (SSM, TSB) PRIOR TO ORDERING)

Снято с производства

RH MANIFOLD AND FRONT CONVERTER ASY. MALE FITTING AT THE EGR CONNECTOR - (NOTE: FOR WARRANTY REPAIRS - CHECK FOR TECHNICAL SERVICE PUBLICATIONS (SSM, TSB) PRIOR TO ORDERING)

Снято с производства

INLET PIPE ASY. (3-BOLT HOLE EXIT), WITH THE BOSS FOR THE CATALYTIC MONITORING SENSOR.

Снято с производства

INLET PIPE ASY. (3-BOLT HOLE EXIT), WITHOUT THE BOSS FOR THE CATALYTIC MONITORING SENSOR.

Снято с производства

INLET PIPE ASY. (2-BOLT HOLE EXIT)

Снято с производства

BRACKET, DOG-LEGGED BRACKET WITH FOUR HOLES ATTACHES THE THE 5246 TO THE ENGINE.

Снято с производства

COUPLING CLIP BETWEEN CONVERTER & PIPE

Снято с производства

PIN AND CLIP ASY.

Снято с производства

GASKET, (DOUGHNUT-SHAPED) CONVERTER INLET

Снято с производства

GASKET, 3-BOLT HOLE, FLEX-TUBE INLET AND OUTLET

FLEX TUBE

Снято с производства

INSULATOR, AT FLEX TUBE

Снято с производства

SPRING, MUFFLER INLET PIPE

Снято с производства

CONVERTER ASY. (WITHOUT BOSS FOR EGO SENSOR ON THE EXIT TUBE)

Снято с производства

CONVERTER ASY. WITH A TWO-MOUNTING-HOLE INLET FLANGE

Снято с производства

GASKET, 2 BOLT HOLES

Снято с производства

BRACKET, FRONT MUFFLER SUPPORT. L-SHAPED ROD WELDED TO A 100X35MM BRACKET WITH TWO MOUNTING HOLES.

Снято с производства

INSULATOR - OVAL SHAPED

Снято с производства

MUFFLER, REAR

Снято с производства

MUFFLER, FRONT

Снято с производства

RUBBER INSULATOR, MUFFLER SUPPORT - OVAL SHAPED

BRACKET, STRAIGHT ROD, 6 1/4'' LONG

Снято с производства

HEAT SHIELD, UPPER AND FRONT

Снято с производства

HEAT SHIELD, UPPER AND CENTER

Снято с производства

SHIELD, EXHAUST PIPE, LOWER

SHIELD, CONVERTER

Снято с производства